Wednesday, September 23, 2009

Implementing A Quality Management System

Implementing A Quality Management System
An ISO 9000:2008 quality management system can be implemented by following the steps detailed as follows:
1. Evaluate the organization’s need/goals for implementing a QMS Need may arise from repeated customer complaints; frequent warranty returns; delayed deliveries; high inventories; frequent production hold-ups; and high level of rework or rejection of products or services.
At this stage, identify the goals which you would like to achieve through a QMS, such as customer satisfaction, increased market share, improved communications and morale in the organization, greater efficiency and profitability, etc. Another objective in implementing a QMS may be a demonstration of compliance through third party certification, which may be requested by an important client or required for enlisting as a supplier to large companies, e.g., original equipment manufacturers (OEMs).
2. Obtain information about the ISO 9000 family
The persons identified for initiating the development of an ISO 9000 QMS need tounderstand the requirements of ISO 9001:2008 as read with ISO 9000:2000 and ISO 9001:2008.
Supporting information such as quality management principles, frequently asked questions (FAQs), guidance on clause 1.2 (application) of ISO 9001:2008, guidance on documentation requirements of ISO 9001:2008 and other brochures are available free of charge on the ISO web site;
3. Appoint a consultant, if necessary
If, within the organization, you do not have adequate competence to develop a QMS, you may appoint a consultant. Before doing so, it is good to check his/her background; knowledge about the product realization processes of your organization; and experience in helping other organizations to achieve their stated goals, including certification.
Carry out a cost-benefit analysis of hiring a consultant and agree the scope of his/her work in writing. It is also possible to appoint a consultant only for the training of key staff; the latter can then carry out further training and development of the system.
4. Awareness and training
Raise awareness about QMS requirements amongst all personnel performing activities that affect quality. Plan for and provide specific training on how to develop Quality Manuals; on procedures; on QMS planning; on how to identify and implement improvement processes; and on how to audit compliance with the QMS, etc.
The Institute of Quality Assurance (IQA), the American Society for Quality (ASQ)and the International Auditor and Training Certification Association (IATCA) can provide lists of training organizations.
5. Gap analysis
Evaluate gaps between your existing quality management system and the QMS requirements of ISO 9001. Prepare how to bridge these gaps, including by planning for any additional resources required. Gap analysis may be carried out through selfassessment or by the external consultant.
6. Product realization processes
Review clause 7 of ISO 9001:2008 relating to “Product realization” to determine how the requirements apply or do not apply to your company’s QMS.
The processes covered by this clause include:
• Customer-related processes
• Design and development
• Purchasing
• Production and service provision
• Control of measuring and monitoring devices
Note that if your company is not responsible for preparing the design of your product, you can exclude the requirement for “design and development” from your QMS and explain the reasons for doing so in your Quality Manual.
7. Staffing
Decide on the responsibilities of the persons who will be involved in developing and documenting the QMS, including the appointment of a management representative who will oversee the implementation of the QMS. Establishing a project Steering Committee may also prove useful to oversee progress and provide resources wherever required.
8. Planning a time frame
Prepare a complete plan to close the gaps identified in Step 5 to develop the QMS processes. In the plan, include activities to be performed, resources required, responsibilities and an estimated completion time for each activity. Clauses 4.1 and
7.1 of ISO 9001:2008 provide information that should be used when developing the plan. The total time required for each phase (planning, documentation, implementation and evaluation) depends on the extent of the gaps in your existing QMS.
9. Draft a Quality Manual
In your Quality Manual;
• Include how the QMS applies to the products, processes, locations and departments of the organization;
• Exclude any requirement with justification for doing so as decided in step 6
above;
• Refer to or include documented procedures for QMS;
• Describe the interaction between the processes of the QMS, e.g., the interaction between product realization processes and other management, measurement and improvement processes; and
• Draft the quality policy and quality objectives for the organization.
The staff concerned in the organization should review the Quality Manual and the documented procedures so that their comments and suggestions can be taken into account before the Quality Manual and procedures are approved for issue and use.
The effective date of implementation should also be decided.
10. Carry out internal audits
During the phase of implementation of some three to six months after the documentation has been written, the trained auditors should carry out one or two internal audits covering all activities for the QMS, and concerned management should take corrective action on the audit findings without delay. Wherever required, revise the manuals, procedures and objectives. After each internal audit, the top management should review the effectiveness of the system and provide necessary resources for corrective actions and improvements.
11. Apply for certification
On satisfactory completion of Step 10, and if your company decides to obtain third party certification, you can make an application for certification to an accredited certification body. The certification audit process is explained section VII.
12. Conduct periodic evaluations
After certification, the organization should periodically conduct internal audits to review the effectiveness of the QMS and see how it can be “continually improved”. The organization should evaluate periodically if the purpose and goals (see Step 1) for which the QMS was developed are being achieved, including its continual improvement.

No comments:

Post a Comment